This guide provides instructions for installing loft insulation rolls and floorboards. Again, consult an expert if you’re looking for warm loft insulation or something more complex, like insulating a limited space or preparing your loft as a living space.

Install Cold Water Tank Jacket and Pipe Insulation Before Insulating. It is crucial to protect them when possible.

  • Measure the cold water tank beforehand.
  • Purchase suitable tank jacket and pipe jacket materials.
  • Install tank and pipe insulation before starting to install loft insulation.

Install Your Own Roof Insulation if you install your own

Roof insulation, you can purchase roof insulation in various designs and thicknesses and accessories, such as supports for installing floorboards, at a large hardware store. You can buy it. Other types, such as Eco and Multi foil insulation, are available online.

What you need

1. Insulation

Once you have decided on insulation, consider how much you need. Note that the loft insulation roll width is usually 1140mm, as the distance between joists in most houses is usually 400mm or 600mm. Most insulation rolls are perforated, so you can easily cut them in half or thirds depending on your space.

2. Snap-off knife or panel saw

Insulation or panels should be cut precisely to the dimensions of the joists.

3. Crawl boards

If you want to use the space for storage, you can buy floor panels or crawl boards at most hardware stores.

4. Storage stanchions

If you use a clipboard and want to maintain a 50mm ventilation gap to ensure good airflow and avoid moisture, you can add these stanchions.

Protective equipment – goggles, masks and gloves are suitable for this job.

5. Staple Guns

The area of ​​insulation covering the loft hatch should be kept safe and tidy by wrapping it in one of the plastic wraps containing the insulation or in a plastic carry bag. I can. Just secure it with a staple gun or big-headed thumbtack.

Loft Insulation Installation Method

If the loft joists are standard, insulation rolls can be used.

  1. Place the first layer between the joists, the horizontal joists that make up the loft floor.
  2. Then lay another layer at right angles to the first layer to cover the joists and make the insulation up to the required depth – it needs to be 270-300mm (27-30cm) deep.

Insulate around electric cables. Insulation shouldn’t be laid over any electric cables. Clip them to the roof joists if you can, or gently move them out of the way whilst you install them before placing them back over the insulation once you’ve laid it.

Insulated Loft Floor Installation Instructions

The planked loft is the perfect solution for the organization. Having extra storage space in your loft can give you more usable space in your home, increase your resale value, and make for a better living environment. Start by getting rid of your storage items. Use good lighting whenever possible.

1. Measurement

Measure the area you plan to climb to calculate the number of shingles you need.

2. Purchase materials

You can buy different loft panels online, including moisture-resistant particleboard, general-purpose hardwood plywood, and more. You may also purchase supports or stanchions to create the required 50mm gap between the insulation and the panel. Materials cost just £300, depending on the size of your loft.

3. Install the support (if you need to raise the board).

First, attach the supports to the ceiling joists.

Install them at a distance of about 1m.

4. Install the floor panel

  1. a) Place the first shingle over the joists.
  2. b) Make sure the edges of the board stay on the joists. If this is the case, trim it to go only to the midpoint of the joist so that the next board can be securely attached to the joist.
  3. c) Use approximately 2-3 screws per connection.
  4. d) Lay another roof shingle. Lay them in a staggered, brick-like pattern to strengthen and stabilize the planked area.
  5. e) Always check those tongue-and-groove connections are correctly installed.

5. Add a fill if desired.

Continuing the staggered pattern inevitably leaves some gaps in the trimming. However, these gaps can be filled with filler pieces that can be cut off into small pieces.